جلد 35، شماره 4 - ( 10-1403 )                   جلد 35 شماره 4 صفحات 15-1 | برگشت به فهرست نسخه ها


XML English Abstract Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Ngo T, Tran B N, Tran M D, Tran T L, Dang T. Influence of Al2O3/MoS2 hybrid nanofluid MQL technique on cutting forces and surface roughness in hard turning using CBN inserts. IJIEPR 2024; 35 (4) :1-15
URL: http://ijiepr.iust.ac.ir/article-1-2087-fa.html
Influence of Al2O3/MoS2 hybrid nanofluid MQL technique on cutting forces and surface roughness in hard turning using CBN inserts. نشریه بین المللی مهندسی صنایع و تحقیقات تولید. 1403; 35 (4) :1-15

URL: http://ijiepr.iust.ac.ir/article-1-2087-fa.html


چکیده:   (146 مشاهده)
Improving hard machining efficiency is a growing concern in industrial production, but environmentally friendly characteristics are guaranteed. Nanofluid minimum quantity lubrication (NF MQL) has emerged as a promising solution to improve cooling and lubrication performance in the cutting zone. This paper utilizes Box-Behnken experimental design to identify the influences of Al2O3/MoS2 hybrid nanofluid MQL hard turning using CBN inserts on surface roughness and cutting forces. Mathematical models were employed to predict thrust cutting force, tangential cutting force, and surface roughness in hard turning under MQL conditions using Al2O3/MoS2 hybrid nanofluid. The study results reveal that the minimum thrust force (Fy) occurs at a nanoparticle concentration of 0.5%, air pressure of 5 bar, and flow rate of 236 l/min. In comparison, the tangential force (Fz) reaches its minimum at a nanoparticle concentration of 0.8%, air pressure of 5 bar, and airflow rate of 227 l/min. The minimum surface roughness was achieved with a nanoparticle concentration of 1%, air pressure of 4.7 bars, and airflow rate of 186 l/min. Additionally, based on the multi-objective optimization, an optimal parameter set of NC=1%, p=5 bar, and Q = 210 l/min was identified to bring out the minimal values of surface roughness (Ra) of 0.218 µm, thrust force (Fy) of 115.9 N, and tangential force (Fz) of 93.3 N.
     
نوع مطالعه: پژوهشي | موضوع مقاله: فرایندهای تولید و سیستم ها
دریافت: 1403/5/16 | پذیرش: 1403/7/23 | انتشار: 1403/9/20

ارسال نظر درباره این مقاله : نام کاربری یا پست الکترونیک شما:
CAPTCHA

بازنشر اطلاعات
Creative Commons License این مقاله تحت شرایط Creative Commons Attribution-NonCommercial 4.0 International License قابل بازنشر است.

کلیه حقوق این وب سایت متعلق به نشریه بین المللی مهندسی صنایع و تحقیقات تولید می باشد.

طراحی و برنامه نویسی : یکتاوب افزار شرق

© 2024 CC BY-NC 4.0 | International Journal of Industrial Engineering & Production Research

Designed & Developed by : Yektaweb